Please tell me the techniques we can use for orientation of containers. Now a days there are various types of containers which are difficult to orient in packaging line.

Thanking you.

What are factors to be consider for the equipment change over.

factors like running hours etc...

LAP progressive wound armature showing failure in testing, armature with 165 segment & 33 slot what would be the reason?

Carbonsteel SA516Gr70 14mm Plate Pressure vessel welded with 12mm pad with Nozzle.

Our PWHT Cycle Holding Time 75Mts and Rate of Heating and Cooling 150 Deg. Pwht Already completed.

Now customer not accepting the PWHT cycle.

Please give your valuable reply for conv

What are the possible causes of tripping synchronous hydro electric generator (60MW) with shaft current protection?.

Please help me

Rgds

Byju

In a EHV substation , say 220 kV GIS,how is the connection between the generator transformer HV terminal and the GIS ?Is it through EHV cable or OH transmission line can be used for connection ? If so how do we address the question of requisite clearances ?

Regards

Hi,

Does anyone have any information and knowledge to share regarding Vapor Recovery Systems?

Our PM often states that it is a very important part of an Oil Terminal. I do not know much about it so I was hoping for literature or examples that I could learn from.

I was involved with a

how many types of wire connection are there in rtd and whats is the 2 wire ,3 wire ,4 wire ,5 wire and 6 wire connection and there connection principle with diagram?

In need of a Expert in Mechanical Design for a Top Drive Drill System. These are used in Drilling for Oil and sometimes water. Important and timely; Help. If you are this person or know of someone please contact me. Tom@GetESS.com ASAP Must: 1) Know TDS systems there are 5 fabricators of t

Hey guys here in Maryland USA we are lucky if we get more then 10 inches of snow in a season. Over the past week end the weather was nice enough to dump about 30 inches. Today week are now having another major snow fall. Totals predicted to be around 16". Third of the year i believe it's some record

Can anybody tell me the formula for Calculating No. of Light Fittings inside & outside of an Industrial Plant.

ASME B31.1 states in section 136.4.6 Ultrasonic Examination that, "Personnel, procedures, and equipment used to collect and analyze UT data shall have demonstrated their ability to perform an acceptable examination using test blocks approved by the owner."

What are these test block, who provides

i need to have the sensor which sences or detects the dirt or dust and produce a signal... if any body know about the sensor please help me out

Take an ordinary 415v/240v-3ph step down transformer with the primary connected star or delta. What would be the corresponding output voltage across 3 secondary coils if the windings were connected in series.

Dear Sir,

We are planning to procure turret punching machine and finalised on two machines as stated below.

* 2020 R from TRUMPF
* EM - 2510NT from AMADA

Please guide us about ,which machine to buy .We deal with sheet thickness vary from 1mm to 6 mm.Our major consumpti

I am based in the North West of England. My trade is Quality Assurance within Engineering.

I am looking to do a degree in Quality Management (part time/distance learning), can anyone suggest an appropriate degree in this matter, or even a website that will give me some clear information.

T

We all know the difference between efficiency and coefficient of performance, hope.

We have seen the technology being capable of pumping heat, with COP of 2,3,4...

Is it possible to pump electricity as well? Is it possible for an electrical generator to be just a "pump"

The clerk at the hotel in NYC told me that Windows 7 doesn't like wireless, and boy was he right. My service goes in and out, kicks me off, and stays connected but loses Internet access. I had the same problem with an airport wireless provider on the way here. And, when the wireless is working and I

(1). Develop an expression for the calculation of line tension and sag of a transmisssion line conductor suspended between supports at different levels or height, assuming that the curve is parabola.

(2). An over head line at a river crossing is supported from two towers at height of 150 me

our factory transformer idely consume 3 kw consume per hr 3 unit .how to minimize the losses.