I am a 8 years experienced Mechanical engineer with M.B.A (operations Mgnt) looking hardly for a job.Please help me.

srinivigna@yahoo.com.

What are the emission rules in California for repowering a pre 97 gasoline powered vehicle with a deisel engine

Hi I have a request on the backhoe loader( 4CX) JCB or CASE (580M) , I have a project to design a backhoe loader by using a solidworks simulation. i really do appreciate if anyone may provide me with the MATERIALS that been used to design the backhoe loaders, especially for the arms,booms,bucket,

we have a drill rig that runs the latest CAT c15 engine with electronic ECM and i am loking for a way to surge protect the ECM without disconnecting the ECM

the rig is used for water well drilling and we need to weld a lot of casing insitu and so far have had to dissconnect the ECM each time

How to design a AHU cooling capacity for a office area as base on the following information;

1) Floor area is 2720m2

2) base on 350 pax

Allan

Hello,

My first attempt at qualifying a new WPS for welding 1.25 Cr -.5 Mo steel "almost passed". Both root bends passed, but one face bend did not quite pass. I am awaiting the bent specimens from the lab. Here is a description of my first process attempt:

1/4" Thick ASTM A387 Grade 11 Cl

Hi - first post here so please be gentle 🙂 I'm after some advice please. I did search around a bit and couldn't find any related messages - hopefully this is the right thread for this topic.

I'm doing some consulting with a client at the moment who have a number of Ethernet over Plastic Opt

How long is this bow which I've just finished?
Cherry belly, Ash back, Waterbuffalo nocks.
A Gooz card to the nearest

Del
(I'll accept imperial or metric, but none of those darned intergalactic or squirrel units)

On concentrating solar power plant (tower reciver) what is the heat transfer fluid which transfer the heat to the water and how can it circulated on the cycle

Sorry guys but it's been a long day and I've been crunching too many numbers and now my mind is just mush

I'm sending two metal working fluid samples out for testing, one is going to have an additive, the other is not.

* End result desired is a 170ppm mixture of a 2-part solution
* Fi

I would like to know the procedure for testing the solubility of the metals lead, cadmium, barium, chromium and mercury.

I have an XRF device, but want to compare the levels from the two different methods.

I need information on the proper acid, time of submersion, and analysis aft

my old gateway gz7339 laptop xp

had been giving me intermitentint blue screen o death warning [too fast to read at start up]

finally wouldn't restart anymore, so I finally gave in & tried to do a full on destructive restore

I can get to bios

I

we want to make automatic gear changing racing cycle then how to fit centrifugal governer in racing gear cycle please help me.

As rare as the Crosley-Fageol flat-8 engine is, at just a baker's dozen rumored to have ever been built, even rarer is the Crosley-based V-8. I was led to believe that V-8 was professionally built, possibly for racing and possibly by Bandini, so I have a suspicion the Crosley V-8 pictured at lef

How do you size the neutral conductor of a wye grounded transformer?

I have recurring water intrusion problem on a PT slab in Erie CO. The 60 x 60 slab was poured for an airplane hangar and voids were left around plumbing penetrations (toilet, shower, plumbing vent etc. The slab is about two years old and during construction, (of course) there were no problems. Since

why do we use fractional pitch winding in Alternating current(AC) machine design

Dear all, I have problems with woodworms that have started destroying my wooden ceiling, could some out there advice me on the best pestcide that I can use without affecting the people in the house and my two lovely cats that stay in the house. Luyombya.

I want to buy a house but a high voltage substation is so near from it. does it affect the human health..is it Risky and Dangerous due to the high Electro magnetic field??

how to wire to the mag starter on a single phase 7.5hp air compressor