Follow the link below

Click the open the interactive transcript right of the player

hello,

currently i am working on the chiller controller for printing purposes, the chiller board consist of TXD, RXD, +5V, gnd, DSR, and DTR only, any idea on which cable from 25 pin serial port to be connect to the controller to obtain a normal black and white printing only?

Hello,

While manufacturing Hydraulic Hoses what all QA/QC inspection are done.Which standard is following?What standard for testing?

whether Hydraulic Hoses after crimping needs Pressure Test or not?

Dear Sir ;

Could you provide me with the standard height for the boilers chimney over the roof. Regard

is it possible to downgrade a laptop from windows 7 to windows xp

Guys,

Anybody knows the importance of installing earth lug in piping. In my current project, earth lug in ammonia lines was remove for some reason. Please help...Thanks..

Dear all,

If we are using a simple paint brush for coating a epoxy pipe lining, what are the chances that it will be 125micron thick only in first coat? Is this way of painting good for long term coating? As the damages are restricted to peeling and scratches, even the company officials are s

Hello,

What precautions to take to the welding SA 533 ASME II-A material.

Best Regards

I thought I would bump the discussion in an effort to put it back on the daily digest.

As always feel free to copy or link to the other discussions:

The original thread Shipping Container Housing is over 1500 posts long

http://cr4.globalspec.com/thread/49244#newcomments

We start

Hi All.

I would like to know what is the relation between radians and mm where radians is the measure of angle of twist. Any help will be good.

Dear all

I want to ask one thing that if we fill the oil in transformer up to 3/4 level ,and now the level in conservator is showing full level from last 8 to 9 day ,what will be the reason

Do we need to check standard flanges(ASME B16.5) as per appendix-2 of Section Viii Div.1, what if the standard flange fails as per PVElite in Bolt area requirements or bolt spacing, shall we consider it safe only because it is within the pressure temperature rating, also do we need to consider corr

I work for a foreign company in foreign country. I was hired as an engineering manager for a construction company. I have a NV Civil Engineering license. If I needed to seal something, what will I need to use. Does the U.S. have an international stamp? I'm pretty sure I can't use my NV license t

mangosteen is popular in the philippines nowadays because its in season again. we try not to put to waste the pulp which we clean using tap water; after which we cut into thin slices and with about a cup of the sliced pulps, we put in about one liter water that has boiled and cooled down a minute ag

Hello everyone,my name is hao.

I work in chang chun university of science and technology in china.My laboratory need a magnetic levitation stage(magnetic suspension stage).It will be used as a sample stage(wafer stage).I have searched the company which can product it for a long time,bu

Can someone please explain to me why does everyone say that flanges are the weakest part of the pipeline? Because the flange is usually so much thicker than the pipe, so why are the flanges weaker than pipes?

http://www2.mdanderson.org/depts/cpm/standards/details/ee-260526-01.pdf

take a look at this and tell me pls what does" ground loop" mean here? ground loop is a case not a real loop made by a conductor as seen here isnt it? so what does this mean in fact?

Hey,

I work on towers, antennas, transmission line, ect.

An associate was asking me about testing T1 line. I told him I wasn't that familiar with testing t1, he told me they use a signal meter called a t-bird, now I have a fair understanding of electrical and em theory. Can anyone

Hi All

Do anybody know some OEM Manufacturers of mincerplates for meat grinder

Thanks Pemo

i am regular browser of artcles in CR4 but haven't made any posts so far. I enjoy going thriugh the various dicussions.Now a days, I have observed that a lot of questions on seminar topics are being posted here in our forum . I would share a seminar topic resource on internet which i came across rec