hi I have been having trouble with a question and i think i've finally done it. I was wondering if there is anyone that can confirm that i've done this correct.

Here is the question: Question 3 A flywheel has a mass of 700 kg and a radius of gyration, k of 0.7 m. What is the torque requi

We are grinding Calcium Carbonate using a ball mill and classifier for particle size control. We are interested in coating this CaCO3 powder with Stearic Acid.

Is it possible to manage the coating within the existing ball mill and classifier arrangement?

What would be the b

I've tried, in vain, to keep the speaker, power and transfer cords at the back of TV, Hi-Fi, disk player, surround sound and satellite decoder from becoming a rats nest of wires. I can pack up my laptop very carefully and move to another room and have a mess with the power cord, mouse and the modem

i am a faculty of diploma engg classes and urgently require solution to the following questions.

1)front 20mx50m of a concrete building in an industrial town is to be illuminated by projectors fixed on ground 50m away from the building.estimate the number and size of the same

2)a 220v,500r

We got IE7 at work. I need to print like 100 procedures. These are word document linked on the web page. I tried

1)

file>print> 'options' tab> 'print all linked documents'. However, only thing that managed to do was waste paper as that printed only the url at the bottom and the pa

Hi every body,i need to use a good refrence for table branch connection,

now i ordinary use the table branch ASTMF681,

BUT I'M LOOKING FOR THE BEST REFRENCE THAT'S COMPARE WHIT PRESSURE?

(for example i want to connect the 1" pipe to 5" on 20bar pressure,what's your best suggestoin ?so

WHAT IS SUB COOLING? IS THERE ANY EFFECT OF SUB COOLING ON STEAM TURBINE PERFORMANCE?

I Got a free monitor, that supposedly only needed to have a mount made.

I ran through the menu & set it up to use as a monitor for my linux box

Looks fine for 30-45 seconds & goes black

here are the details:

Tru Tech

mod 008-09-0119

ser f1bia85016745

I have a block of opaque white (or nearly so) plastic. I want to use it in a critical application as a capacitor dielectric. I could be Nylon, Teflon, Delrin, Polypropylene, or ? How can I identify which material it is?

what is cathodic protection? plz explain with diagram and practical application in power industry,

Ransomware got its start in 1989. Back then, it was relatively ineffective. That's changing, which is bad news for us.

One of my neighbors recently experienced ransomware first hand. Up until then, he had no idea it existed. Because of that, it seems important to revisit extortion malware, expl

If you could travel back in time to the Victorian era (say 1880), with one item from today, what would you take to most impress the people of the time?

Thanks Guys

My problem is that I have Two MS units that move in and out and I use two pieces of rod sliding inside two tubes and to attempt to beat the rust problem I thought it could be a good idea to use stainless for the rods and tubes, to manufacture the whole thing in

I have a non uniform air gap in our induction motor i want to know the effect of this problem in the performance of the motor.

Hello Everyone!

I was hoping that some of our computer savvy members may be able to help me locate a freeware or shareware package. I'm stumped and need some advice!

The type of software I'm searching for must be able to convert a scanned document or drawing

2nd Try.

I need help. I have a 6 wire output (SoG?), and a 5 wire input YRB+RW. What do I need to make this work?

Coming out of my device is six wires: Red, green, blue, yellow, red, white.

Going into the back of my monitor is: Red, blue, yellow, red, white.

It se

Which is the Best Grease for wheel Bearing Lubrication For LCV and HCV? Fuchs or Castrol or shell?

Is there any moisture level acceptance limit in Lubricating oil.Pl. give some standard referance also.

hi every one

i would like to ask that which system i use for car painting workshop to airconditioned this and as well as ventilation........

why control valve size is usually less than run pipe size