is the capacitive type transducer best for level measuring for continuous measuring of level?

Does anyone know if a rule of thumb exists for calculating what the high discharge temperature shutdown set point should be for a reciprocating compressor based on the theoretical normal operating temperature of the discharge valves? The TC is installed in the discharge manifold.

hi

il will be performing an survey in our plant. I will be survey all the electronic equipment and checking whether it is protected adequatly against lightening,faults etc. need to check whether earthing is properly done.and whether surge arrestors are installed on sensitive equipment. also

I would like to know what is the cross sectional area required for copper mat used for earthing a normal residential building? i know it will depend on the fault current and soil resistivity. but can i get some ball park figures.?is their any standards for earthing usinng copper mat for residential,

This power plant is considering converting a generator to synchronous condenser operation. If anyone has experience with this, I would like to hear about it: challenges, cost, operational issues, maintenance issues, equipment changes, etc. There are 2 large generators (ST prime mover) on the order o

I have an air mover. This is a unit that uses a small amount of air to drag in a larger amount of air. The problem I have is that the air is going down a small diameter tube. This tube gets momentarily blocked. This really plays with the principle of the airmover and it decides to blow air the oppos

To run hydraullic machine at load of 600 ton which oil should be used?

Any idea for cost down for plastic part (injection moulding). I need to brain storm some ideas.

Sir,

Please provide me the drawing of earth pits which is suitable for instrumentaion.

Dear friends,

I have a two stage reciprocating compressor of following specifications:

LP Bore - 385mm, HP Bore - 235 mm, Stroke - 150 mm, FAD 21.27 Cu M/Minute, Max delivery Pressure - 7.5 Kg/cm sq, RPM - 750 KW. The compressor is oil lubricated and water cooled. The description of mo

DEAR SIR,

WE KNOW WHAT ARE CHEMICAL ARE USING SSD CHEMICAL FOR BLACK CURRENCY

CLEANING? WHAT IS THE RATIO OF MIXING?

REG/SRI

Good morning.Thanks in advance for your support and help that I have had here from everyone.I'm working for a company that use more Siemens PLC (simatic v5.4+SP1) I'm there one year know. And sometimes when I have problem and I didn't have alarm on the screen, I truly don't know where to look. Just

please give a information about a 3-axial load cell for measuring a ground reaction force to construct a FORCE PLATE DEVELOPMENT in gait analysis.I will be very thankful you if you provide me.

Why all marine Specifications calls for 3 Times short circuit current from the alternators?

In our power plant a EOT Crane of Max. loading capacity of 375 Tonne was erected and commissioned. Now we want to do the load test to get the loading capacity how can we get ? the necessary arrangements and other possibile facilities are required for this?

Sanjay Rawat

Engineer

Generator CAT3306 - 180kVA - 380V output...when running for hours. Suddenly output voltage drops to 300V, same rpm/Hz drops during 2minutes, then rpm quickly goes up and frequency passing 54 Hz and generator engine goes off. Same symptoms come up after restarting. What do you guys think...\r\nThx fo

How to check the no load loss of the Alternator?

We do measure the Input power of the Prime Mover coupled to the alternator, but the Losses of the Induction Motor are not considered, Secondly the PF of the Induction motor running at very less load is also unknown?

i wanna ask u one question about thread length tolerances. is ansi and uni is same standard ?? what is the uni standard of screw threads parts , and plastic parts. and what is the tolerance lenght of thread if actual value is 11.50 .

waiting ur early reply

thanks

We picklie Duplex stainless steel with Nitric and HF. The solution is supplied to us as 26wt%HNO3 and 7wt%HF solution mixed in water.

We then further dilute the the above liquor 2 to 1 with water.

I am trying to calculate the pH and the chemical reactions but the combination of the

What is the most adviseable product as per your experience, for online repairing of leaks in Crude oil and natural gas? Operating pressure of pipelines vary from 30 to 350 PSIG. material of construction for pipeline is as per API norms.