Not sure if this is a suitable question for this forum, if not please say so.
If I have a fractured knee cap that has/had fluid in the joint which has not been drained, where does this fluid go? How long or how does the fluid go away? While wearing the velcro removable cast/brace the foot and a
Hello,
I want to do light energy saving simulation (based on daylight availability) where each luminaire consists fluorescent tubes (T5,T6 or T8) with a dimmable electronic ballast, which can dim the lamp output smoothly and uniformly.
I have to know luminary coefficient of utilization
From Inside Rensselaer (RPI electronic publication): "Acoustics expert Henry Scarton, associate professor of mechanical, aerospace, and nuclear engineering and
director of the Laboratory for Noise and Vibration Control Research, has been named a Life Fellow of the American Society of Mechanical En
Can somebody tell me where to find the journals and articles about the psychology approach in industrial engineering. Furthermore, am also looking for appropriate articles and journals concerning of layout in manufacturing.
I try to find in internet,but the information is not enough for my
Hi, i'm a 2nd yr mechanical student. I would like to do a cost effective mini project. If anyone can help me pls respond to this. U also can contact me in my email id gap.cdm@gmail.com.
did some body tell to me about amf electronic circuit diagram
i m a starter in plcs ladder logic programming. i just wanted to clear the doubt that is it possible to on off an output without using two seperate contact input one to on and the other to off it. if its possible please help me how to do it.
hello,
Till date I have known that the filter rated as 3 micron will have more pressure drop than that of the filter rated as 10 micron.
So, pls let me knw, is it possible to design a filter of 3 micron rating having pressure drop less than that of the filter having 10 micron ratin
Dear Madam/Sir
Please help us by indicating the above mentioned test circuit according to IEC.
We would be very thankful to you.
Very best regards.
can anyone provide data sheet for Soft starter of motor
Hello All,
We are into the business of cold drawing mild steel and alloy pipes to the size required by the customer. The process of cold drawing requires intermediate annealing. But when we anneal the pipes (to temperatures of around 950 degree C) in our 'closed bogie type oil fired' furn
I have seen dual magnets on some speakers, with the extra magnet behind the other one. Can this really improve the speaker's performance? If yes, would i benefit if I try to stack the magnets by (1) letting one pull the other or (2) forcing it to come together as they push each other?
ELBOW,FLANGE,EQUAL TEE,ECC REDUCER SURFACE AREA CALCULATION
1-Can we use ACB for a 600KW LT motor which is feeding through 690v ac power supply. if so then what will be the appropriate ACB rating ? needs ur guidance thanking u.
2-What is the advantage of HT motor over Lt motor which is costly and what is the cosst difference for a 600kw HT moor &
What is the Difference Between ASTM A105 & ASTM A105N & ASTM A105M
i want to make water boat so which moter i can use & which type of fan i can use for running my small boat?
Hi!
Can anyone advise me if there is an alternative to Hagglunds's Compact motor?
This type of motor is a cam-ring type with a rotating hollow shaft.
Thanks...
hello,
pls help me out,
I want to achieve the cleanliness level of NAS 3 for a fluid in a hydraulic system. I want some idea as how should I select the filter rating to achieve the specified cleanliness level.
Dear All,
i have facing problem of damage of impleller and casing of PFA lined pump.calcium chloride solution having concentration 20 to 50% contains acidity as 1%. during circulation of above solution at 120 to 130 degc pumps were damqaging.
how i can prevent the above
Hello
I got siemens MP377 with loader Version 1.0.2.0_1.83 and WinCC flexible 2008.
WinCC flex project shows only MP377 devices with version 1.0.0 and 1.0.1.
If I select version 1.0.0 it disables compile command.
If I select version 1.0.1 it compiles the project and work