Hi! My design of Flue gas heat recovery system is complete. I am utilizing heat pipe stack to pre-heat the feed water using the heat from the exhaust flue gases of a boiler. The temp of flue gas at the entry of the system is at 230DegC. I am stuck with the selection of the material for the casing. C

i want to improve my drawing reading knowledge i.e surface drawings please send me any drawings to this mail s

I'd like to know about Sheath Voltage Limiter. Suppose my system has 10 outgoing fdrs. Is it possible to use only one set SVL to protect all 10 fdrs? I like mean that all earth shunts of all cables will be connected to a common bus and that bus will be connected to earth bus via SVL.

Is it po

A car fitted with MPFI engine should not be started with the accelerator pedal pressed. Why?

What is the best method available for the prvention of ,insects, rats and snakes into the food product industry.It is given to understand that Carbonic acid ,if it is sprayed on the walls may prevent the entry of insets.Can anybody throw somelight on it.

Dear Sir,

The mould temperature controller tries to keep the mould temperature constant depending upon the molten substance e.g. whether plastic, zinc or aluminium or their alloy being used. Assuming it is begining of the process when the mould temperature is assumed to be the ambient atmos

I just installed a 20 gallon fish tank, filled it with tap water, gravel, and some live plants. It is lit by an Incandescent bulb and has a water filter - no fish yet. It seems that ever since I installed the tank my home wifi signal is flaky. Signal strength has gone down throughout the house.

im working with a voltage relay sensor for generators with just using a magneitc relay series with a resistor dc supply is 24v dc. operation is the relay is partially energized dc supply is less that 24 v dc. as the generator starts up dc voltage decreasing so relay was de-energized which is normal

hi friends i have reliance vs drive electric in dc drive week end off the motor and again motor start have long time take to run i put one 100 w bulp to provide the drive panel please remedy problem any one have idea

Hi to all

I have a a toroidal choke core ( RadioShack #273-104),it has AL 175 mh/1000 turns.

So i can make 1.19 mh choke by using 82.5 turns.

My question now:

Can i use it for any current by selecting the right wire size ?

Does a high current could take i

Hi, I have a wireless network set up, and have 2 computers on it; Mine (which has the printer attached), and the other one. I have set it up for file and printer sharing, and I can access the shared docs on the other computer, but the other computer can't print wirelessly. Every time you try to

This morning, Tom and Ray on Car Talk got a call about parking chairs. The gist of their answer was that it depends on where you live. In North Boston, apparently, it is considered good manners to slash the tires on anyone who violates a parking chair, but in other cities, it's unheard of.

98 dodge ram cummins diesel, dash lights and gauges stopped working, all other lights work. checked alternator and only getting 11.65volts of charge is that unusual?? i recently changed both batteries and alternator, but the dash lights and gauges problem already existed before replacing both. what

I recently put a new transmission in and now my engine stalls when it is running for about 20 minutes. If I let it sit for about the same amount of time it will again run for about 15 minutes and the does it again. I pulled the codes and got 12,43,34,55. I've replaced the coolant sensor but the p

i want to know that how much WK coil have to be use for generate 1450 degree C in the furnace?

Hi to all of you.

I have been on board a vessel today and I was shown a winch that has a 24 volt motor with a 90:1 reduction gearbox. The motor was burnt out due to too much duty cycle running a towing winch for a tow fish(sonar side scan). After the gearbox is a chain and sprocket arrangement

can you describe the role of a standards engineer?also what tasks he performed. thanks Don

what is velocity of piston of hydraulic cylinders around 20 bars pressure acting on it, for 60-70 mm of stroke.

At 31 years old Shaundra Bryant Daily has already made an impact on the lives of young girls around the world. Born in Nashville, TN, Daily received a B.S. in Electrical Engineering from Florida State University (2001), a M.S. in Electrical Engineering from Florida A&M (2003), S.M. in Media

Looking for a few good contacts or companies that have an R&D Department and would focus on Nonlinear Vibrations for Fluid Structures?

Help is appreciated!

Thank you!

Jake