Dear all

Can anyone give me information about the available sizes (any vendor) of Level control flanged valves(not threaded or socket weld). I am not sure about the small sizes i.e whether 1/2" or 1" flanged valves exists or not.

so far we have used threaded level control valves...

Hellow every one.

What is the formula to convert the breaker MVA rating into KA & vice versa.

Thanks

Hi! Friends,

I am having a problem in calculating Fan power, Plz. help me out,below is the details of problem.

I have to select one High pressure centrifugal fan which will suck air from atmosphere & will deliver in a high pressure fluidisation Air line.The atmospheric

Humpty Dumpty sat on a wall without a harness and lanyard in flagrant breach of Health & Safety at Work legislation.

Humpty Dumpty had a great fall that was reportable under RIDDOR.

All the King's horses and all the King's men (some sort of QUANGO?)

Couldn't put Humpty

I would like to know what are the benefits of installing the VSD on the coal correct medium pumps.how can I justify the savings

centrifugal pump model 250/200krebs726 , 10/8/24

motor rating 275 kW

Actual motor output average 245kW at sg 1.73

flow 7

Dear,

I made a potable water tank with S.S 316L 3mm sheet.In that some are getting crack on its belly position exactly on its heat zone(Just above the welding)I used 316l electrode and I feel that my procedure is correct and same as earlier.How it si happening?.Any material problem or w

i want to do simulation on the IC engine to improve the performance of the engine for that i need mathematical model of the engine...and i read thousands of papers regarding this but i am confuse in some details so i need some help of the some masters in simulation...by the way i want to add one mor

Hi friends,

Can anyone help about the following???

How the zener diode behaves when it is put in series, like in the reverse bias mode?

what will happened to Alternator, Rotor in case of reverse power?

i have installed a vfd drive of siemens for 80 t crane in my company .

the matter is this ,that the resistance gets heat up very much after few operations and it opens .

so anyone pls give me their valuable suggestion to rectifiy this problem .

thankyou

how to select a starter motor for automotive application???

Does anybody know where I can get an ISO Welding Symbol Chart, preferbly A3 size? It must contain all the symbols with their meaning/ explanation. I want to laminate it and put it up in the workshop as a reference. Thank you.

how do i delete my comments which have been posted on the forum

How can I design the Rotor resistance starter for 1600KW, 6660volt,165Ampere,992rpm, Rotor Voltage-1795, Rotor Amp-530 HT motor.

If any detail required kindly contact me on mkhandelwalss@yahoo.co.in

im making a wind turbine for my final year project.i want configuration of ac generator /alternator to match my wind turbine output.so anyone suggest me the configuration or the site to which il get it...pls guys help me out

Hello Guys, please help me, i just want to know if SAE 52100 (ASTM: A-295) can also be use to fabricate a helical gear and why? but i know that it is good for bearing.

Hi All

We have got for repair one small DC Motor Westing House make 7.5 HP RPM 1750/ 3000 Volt 240 amps 27.8 amps duty 24 hrs shunt motor TEF ,Frame 256-A, Application for rubber solution mixing.We have received this motor for overhauling and we have noticed solder comming out

What is meant by Double Block and Bleed Valve arrangment?

Does it mean........ A ball valve (upstream), a bleed branch connection, 2nd ball valve(upstream), 2nd bleed connection, control valve, bleed connection, ball valve(down stream), bleed connection and ball valve(down stream)

How did we ever as American citizens let the credit card people, the banks and all of the other financial institutions that we deal with make this credit fraud our problem? I mean we did not do it someone did it to us so should not the person that accept the information is stolen card be held accou

I have found that some appliance companies send a very specific book on high atitude adjustments to their equipment, but the gas range/oven companies don't seem to care. they say to derate it over 2,000 feet, but it still puts out allot of carbon monoxide even by their book. What can be done to redu