From Technology Review RSS Feeds:
Polymers that mimic the body's natural defenses could be a new class of inexpensive therapeutics. For the first time, researchers have shown that a nonbiological molecule called a plastic antibody can work just like a natural antibody. In animal t
My project is developing a renewable generation project in the UK fuelled by veg oil and HHO produced by the electrolysis method.The majority of the technologies, for added HHO, available seem to reduce the base diesel by around 20% at best.My generation is seeking this reduction to be around 50% fo
This question for Forum administrator that when I reply against any post and want to insert a link, the option "Insert Hyperlink" disappears, what is the problem? Where am I mistaking?
How can we relate the no load current and no of turns in ac winding?
Dear All,
Can anybody tell the difference between T91,T21,T23 materials as these materials are frequently used for Super heaters in boilers
Creep resistance, degradation etc..
Thanks
Dear Friends,
We have Rockwell Software RS Logix 5 in the HMI PC of one of our machine. Whenever I want to open the PLC program and go online with PLC, I have to insert a floppy disk having Master Key for software then program opens. Now the floppy disk has damaged and I unable to open the pr
Trying to produce pre-expanded PP beads using an autoclave (pressure of 600 PSI; Blowing Agent = Co2 ; Dispersing agent = h20; Temperature = 150 C).
Constant stirring @ 100 RPM ; Saturation Time = 1 Hr....
Have been having problems getting the beads to be released from the bottom of the aut
Need a transparent, temperature resistant glass/plastic fabricated chamber -- Properties required besides transparency is hot-plate compatibility and temperature resistance until minimum 150 C over a duration of an hr.
Which materials would help achieve my purpose? Any recommended manufactur
What are the values of earth resistance of following installation 1) 33kv and below class sub stations and transmission lines 2) 66kv class sub stations and transmission lines 3)110kv class sub stations and transmission lines 4)220kv and above class sub stations and transmission lines
Transformer Laminations are cut in different shapes as required i.e: EI, EE,E,El etc. and this is done usually by big machines. I am looking for a small portable power/hydraulic machine that can do the same job. Cut laminations from 10 to 100mm + width. If there is one that cannot cut shapes but str
What is difference between flowing & Non-flowing Pilot operated PSV?
Please I need help to understand how all the engineering codes tie up to each other.
When to know which to apply and how they complement or supplement each other...I hope my question is not too vague to answer
Looking forward to a cool response from the team!
We have installed a new motor and connected with a DOL starter. It is not running after switching the start button. What will be the cause? I checked connections in the motor and starter and found it is correct.
Hi Guys
Have a good Day.
Last day I was having a job on pressure transmitter of instrument air, unexpectedly we found water inside the tubing, later on as discussed with colleagues this is a normal phenomenon in summer season. But I am still confused why in summer this happens
Please explain the way of melting sponge iron and scrap in induction furnace.
What are the additives?
How can I control the amount of S (SULFUR)?
Yesterday's blog entry contained a link to a story about Brooks Stevens by Richard Langworth. One of the Stevens' designs that Langworth mentioned was the Excalibur neoclassic, which recently popped up on Hemmings.com. This 1982 Excalibur Series IV just so happens to come from the same year of La
There are many benefits to adding twists as part of a well-rounded yoga practice including relief of back pain and pressure, improved digestion, stretching and strengthening of the spine, and many others depending on the pose. If you have problems with your lower back or sacroiliac joints, do
I am building a band sawmill and changing it from gas to electric. I have heard so much about the differences and need to know how to size the electric motor to take the place of a 9hp Honda. The electric will be 220v single phase.
I want to covert a pulse jet (ram jet) into a fire fighting tool where steam is created within the jet blast. A double walled exhaust tube as well as an in-cased combustion chamber housing.
Mostly my question is how effective is steam in fighting fires, steam combined with an oxygen depleted blas
hello folks,
figure : http://blog.naver.com/nkaier/50090338879
please, see an above figure linked.
I am just wondering which free body diagram is correct, A or B ?
(see how ground reaction forces are drawed from FBD)
and Why?
--------------------