Manufacturer's data sheets for plastics do not normally give continuous and maximum intermittent service temperatures. These are essential figures when deciding on the right plastic for a particular job, particularly where high temperatures - say 150-200C are involved.

Is there any way of p

i just want to know if in electrical circuit, the equivalent resistance of a parallel circuit is given by 1/Rp=1/(1/r1+1/r2+........1/rn). Then is this relation true for parallel piping also for finding equivalent pressure loss in a parallel piping system? since the parallel piping and parallel ele

Hello,

I am doing my project concerning the cognitive psychology approach in manufacturing and my problem is where can I get the information about the relationship between cognitive approach in manufacturing?

Thanks....

Please advise as to how to build a hydraulic press brake. Ideal bed length 5 to 10 feet long. Capacity @ 100 tons. One or two hydraulic cylinder operation.

CR4 Admin - phone number and e-mail address removed

From the Site FAQ: Do not post phone numbers or email addresses. The CR4 A

Well now this is interesting. Since discussing the plywood cars and hydraulic drive systems of Raymond Russell, we've been in contact with Russell's son, Raymond Benjamin Russell, who sent us a much better photograph of the Gadabout than we could find earlier. The gadabout is a remarkable car i

Snakes are fun, but they can occasionally get in trouble.

Nervous Handlers = Nervous Snakes

Never give your snake to someone who is nervous around or scared of snakes. If a friend insists on handling a snake – say, to try to get over his or her

My brother has a sports camp in the mountains of NH. He wants to build a footbridge (suspension) that spans approx. 50 feet, 5 to 8 feet above a creek, which is usually dry. I need a push in the right direction to start some R&D. Could any one help me with ideas? I'm thinking of 3 cable in a t

If the direct buried underground conduit with insulated conductors (carring more than two 120V,1phase lighting circuits) be sealed at the both ends (means air space between wires is locked w/o any breathing capability), would there be any derating of ampacity of current carrying conductors other tha

A process has been described to prepare an aqueous suspension of rubber latex nanoparticles. What would be the practical applications of nanosized latex ?

Who knows the initial high temperature to use the ASTM A106 tube? I can´t find that X°F or X°C.

Regards,

I was polishing a piece of aluminum with a 6" cotton wheel mounted on a 1/2HP 120VAC motor the other evening. This device is plugged into a ground fault receptacle and has the case grounded. The polishing wheel was a 5/8 or 1/2" size mount, with a plastic bushing to allow it to fit the 1/2" shaft mo

On the day in engineering history, the Big Apple suffered an electrical blackout that shook the nation's largest city to its core. The outage began with a series of lightning strikes that crippled some transmission lines and overloaded others. By nightfall, human error and systemic failure dar

Are there are some special sort of Induction motors (Low Voltage) that would be used with the VFD.

Is there any harm in using conventional Induction motors with the VFD?

Hello all,

We have ~80 blocks mounted to our ceiling over each of which 7 runs of 1/4" aircraft cable pass. I am trying to resolve a set of interconnected issues we are having with these blocks. This is a theatrical counterweight fly system with an 80'+ ceiling.

The first (and cl

I bought several 2 bulb 2 X 40 watts armatures without starters. They only ignite when they like. Sometimes i have to try 10 times before they light on. Is there a trick to it?

Several developments near my home use perk ponds to force stormwater below ground level. Now, my basement has flooded several time a year and during the rainy months my septic is inundated with water. What can be done?

Can somebody give some email addresses of manufacturers of tapered circular concrete street lamp posts? In one pole I found the word "BARRATT" but I couldnot find the address

Knowing there are some very knowledgeable people out there, I hope someone can point me in the right direction to solve a keyboard problem.

Operating system Windows XP.

I have just had to replace a motherboard and because of the differences between the new and the old boards had to

Dear Friends,

I am looking for some detail or real picture showing the flexible tubesheet since I would like to getting more knowledge about it.

Any help would be greatly appreciated.

Thanks mate.

Hello All,

Not sure if this is in the right section but here goes anyway. Is there a tool that can be used to create a bullnose / round finish on the end of a 1.5mm Nitinol rod? We tried using a grinding machine but this created more of a chamfer (beveled edge) as opposed to a rad (bullnose) id