Regards!

Inspite of all settings in Control Panel ==>> Mouse ==>> Pointer Options ==>> Automatically ... have been unclicked.

Searched for any program installed but nothing found for this behaviour!

Any tip please !

can anyone help me for the selection of proper filler wire for the welding (GTAW) of copper pipe to stainless steel pipe.Greatly appriciated for the support.

with BR,

Malutty.

Take a case where a power transformer with star-delta configration star side neutral is impedance grounded and delta side is load side. If fault occurs on bus (load side) diff. relay of transformer gets tripped.what are the means available to detect earth fault protection on delta side?

Can you please help me? I am currently writing my dissertation on STATCOM Control. I would like to ask what is the methodology of replacing the DC Voltage in the STATCOM input with a DC Capacitor. The simulations are run on the PSCAD software.

Hello in jacketed pipe used steam ( or warm water ) to save temp. of main line & content do you know any standard that explain how many lenght we shoud give condensate & get fresh steam to line ? Thank you

we have purchase 3lpp pipes 2 years back and stored in the lay down, due to exposure to uv , it started to detoriate polypropylene and now we want to start the actual installation, i scored the detroriated pipe until the powder stop coming and meassured dft, it is arround 2.7 mm(were as new pipe to

what is working principle of AVR SX440?

How it works describe with circuit diagram.

What is all that noise coming out of my computer?

Kate asked me and I told her that it was the electrons going around the corners when the wires were bent too sharply.

She didn't beleive that either.

My old Chev. truck is having one of the few illnesses ever afflicted.

It won't idle. It just dies every time you do anything but run down the road. Otherwise everything is fine. Starts like a great.

I am thinking of 'scoping the idle speed motor wires, but I don't know w

i have a 1996 ford explorer 4x4

the 4wd low light and the overdrive off light blinks on and off

i put my scan tool on and it gave me the turbine speed sensor malfunction error

would the speed sensor cause this and where is this sensor?

and would this keep the 4wd from wor

sir i want to make a electric genretor witch countain no fule. ya i m right. i mean , i assamble to be a electric genretor, in witch no requried of any type fule. so any body intrested in help .... so reply.... i hv some prob in this project.

please could any body tell me what is the oil content in produced water make it allowed to be disposed in open pit in desert according to the regulation

Jaxy is an active contributor to CR4 as both a blogger and a moderator. She typically has blogs running every week in Jaxy of All Trades.

Tell me about yourself (major, college, work experience)

I recently graduated from Rensselaer Polytechnic Institute with a Bachelor of Scien

From The Engineer - News:

Patent applications for satellite-based technologies have doubled in the last five years, according to patent and trademark attorney Withers & Rogers. Based on the company's analysis of the incidence of international patent filings relating to global na

From IEEE Spectrum:

The race to replace copper wiring with optics in chip-to-chip communications reached a new milestone last week as Intel announced it had produced a system using silicon-based photonics to transmit data between printed circuit boards at 50 gigabits per second.

This week's image:

Be sure to vote for your favorite caption!

Is there a forum, user's group, or ?? that deals with nuclear reactors and engineering? A search found a lot of topics about nuclear, but I didn't notice a particular forum or group. Thanks.

Can anyone tell that when we use flush type diaphragm and extended diaphragm in Transmitters and their applications as well. Please someone give some literature regarding this topic.

i face a problem with my avr studio version 4.18.684 that run under windows xp

every time i try to create a hex file this message appear:FATAL ERROR:cannot open output file c:\documents and settings\--------

has anybody know what should i do ?

Has any CR4 member ever build or tried to build a Bedini electric motor, a so called: "Free Energy" motor. Will appreciate response // discussion.