Hi all,

I need to create a 3D prototype of a new component for design checks before it goes for manufacture however i am unsure of a company in the UK that can do this for me, any ideas?

I have V-reg Peugot 206 occasionally when I turn the engine on the accelerator seems to be pressed without me actually touching any pedals, continently revving. I turn the engine off and then back on and for two or three times it will not start, like the battery is dead, and then after will star

actually i am a mechanical engineering student.

i am taking a project to convert air cooler into air conditioner so that humidity produced by cooler can be minimized .so how can i convert the cooler in to an air conditioner in a economic way?

Hello

This is what i do to check if a motor is faulty. I checked continuity between U1>>U2 V1>>V2 and W1>>W2. Also i check ground resistance between the windings and ground. Is these two test enough to tell if a motor is good or bad. Thanks

What is the code for the application for an anti-syphon valve in the fuel supply line at a day tank.

i want to support a hot hollow aluminium sphere vessel (inner temperature around 500degree Celsius,outer is exposed to atmosphere)which is carrying a pressurized fluid(around 120bar) with a outer hollow aluminium sphere. how can i transmit the inner sphere load to the outer one ? it must allow the t

What is the proper way to detect proof stress from metals ? pl. tell formula and graphical rep.

Dear Sir

Please tell how to calculate diesel consumption of a diesel generator.

Thanks and regards

Gurjeet Singh

I am seeking a manufacturer of melamine food service plates. Specifically a 6.5" pie plate. Any help would be appreciated.

Thanks, Tim

Dears

We have pipes having the material test reports with different heat numbers, but heat numbers cannot be indentified due to rust in the surface.

Now we want to use this material, but how I can give heat numbers to this pipes?

Thanks

Why use a calorifier?

There are a number of variable speed drive technologies out there. While some have a uniform power factor close to unity across the operational range (such as the VSIs), others go from anywhere around 0.4 to 0.8 (such as the Cyclos).

So, is any one type of electrical variable speed drive SIGNIFIC

Hi friends, i m mechanical tecn, my problem that our gas engine(1065 kw jenbacher) cylinder temperature very high,checked all parameter fond ok, when engine load up to 60% load cylinder temperature shoot, please help me

Hi, Everyone

We are planning that the power of 415V from several Diesel Generators will step up to 11KV switchgear and come back to 6.6KV switchgear through plant MV/LV transformer to start fire water pump for 6.6kV motor.

In this case, Somebody pointed out that this sceme(Step up and Step

hi dear fellows;

I m working on the solar energy with reference to the electricity production so i have a problem that which solar panel will suit best with reference to its cost & efficiency?also what is the size of this panel?

Is it possible to measure 1 phase current in 3 phase 4 wire KWH meter?

Hi,

I need the information about the CO2 gas... how much gas I need to make the mould hard... what would be the caluculation for that...

Hi All!

do you have seen a recycle line on a check valve? As you know on the discharge line of pumps there is a check valve. Now, why there is a recycle line on this check valve?

I'm looking for a cheap, low power single phase solution to chop/macerate material. The material will range from horse manure (with straw content) to bakery waste to vegetable waste etc so will need to be able to cope with a variety of products. Does anyone know of a solution that is out there?

Dear friends;

I have an electric tram in our Corrugator plant for transferring corrugated sheets from Corrugator machine to conversion machines. The tram has a 7.5kw 380V motor with 11kw inverter (Lenze 8218) for its movement back and forth. Now this inverter has malfunctioned and I wan