put new timing chain in but now it won't start, i have a good spark and good fuel pressure. i have checked out cam sensor and crank sensor, all are good. i have looked for codes but all i get is code 12 memory cleared, because i had the battery unhooked when i changed the timing chain. could i have

Dear All,

We are using aluminium piping in our spice conveying system.

Why not Stainless steel or flexible Piping?

Regards.

Saw this article in the ninemsm website.

It explains why we get so many homework questions.

http://news.ninemsn.com.au/article.aspx?id=8140141

Ok so where is our cut?

I have a 277/480 service with a 120/208 load in a restaraunt I am building. The a/c's (3) and vent hood are 480v. Layin lighting 277v. All other load will be gas or 120v. I understand the calculations fine, but I am not sure how to layout the written load analysis, because of the dual voltages. Can

pls update information about workshops and conference held in any other colleges in tamilnadu belongs to instrumentation

when the 55 kw motor converts from star to delta it trips. But the contactor is latched on. so we started the motor in delta. it runs. when we reverted back to normal star delta fashion the same thing happened. when the timer and OLR were changed, the star contactor was on, but not the main contacto

An AV consultant on one of our projects has requested a separete isolation transformer to power all his rack and room mounted equipment. This is a 8 story building and the equipment is scatttered trhoughout the facilty. We are using a 600 Volt distribution system that uses ZigZag transfomers at each

Dear all,

I would like to know the standard that includes lifespan requirements for pressure parts of big coal fired power plant (such as main steam pipe, valve, steam drum, etc.). Please help me soon!

I have a 100kVA 11kV/0.4kV Dyn11 type transformer. I want to connect a 20kW HydroPower plant to this 11 kV grid with this transformer. So, how can I calculate the size of Drop out fuse to connect HV side transformer to 11 kV grid? Or shoud I use MCCB??

I am using 460/120V AC 150VA stepdown transformer for controling the circuit.i want to know about what is the power consumption of 120 vac coil to start the motor.

thanks

suthakaran

what is the function of a balance leak off line in a feed pump of a boiler ?

Is there a list of browning bar serial numbers with dates of mfg. available?

Thanks - Bob

What are the key characteristics of a successful CEO heading an innovative company? Machine Design editor Leland Teschler describes wish list, which includes overconfidence (characterized by how CEOs manage their stock options), and an "unwavering resolve and workmanlike diligence" for getting work

A current of 50A is carried by two cables in parallel. One cable has a resistance of 0.15ohms-and carries 20A. What is the resistance of the other cable?

Despite laws against discrimination on the basis of age, older workers, those 50 plus, say they have the biggest disadvantage when seeking a job. In fact, employment counselors suggest that age may be the most common form of workplace discrimination. Why do think employers are so reluctant to hire o

See-through OLED panels can be made by either keeping the emitter and driver layers very thin, or by leaving areas empty except for a see-through substrate. A 2-inch 320 x 240 (QVGA) OLED panel, deposited on glass, let more than 50% of the light through. They seem destined for phones — but why

hi every one please tell me about ladder diagram of star delta. regards

Our condensing 5,5 MW steam turbine has been operating

for 4 years without problems.By start after short 2 days shutdown we found out barring gear broken.After repair we tryed to start turbine again but is´t impossible to spinn the turbine.Turbine was stopped right regularly before shutdown.

hi can anyone give me a help with this question please?

i need to find starting voltage of the motor, the percentage of normal torque when the motor is started the motor start current and supply current.

i thnk the point of the exercise is to bring home the point that that trfx for st

Hello,

Is there any software or method to remove water mark logo from an image.

thanks.