When a 58 Kady Krogen trawler recently hauled out at Lauderdale Marine Center, our hydraulics company, High Seas Hydraulics was hired to do routine service on the ABT Trac hydraulic stabilizer system. Our running gear team was also called upon to pull the props and shafts for routine cutlass bearing and seal service. <\/p>\n
Damaged threads <\/p>\n
Once we dropped the stabilizer fin in order to replace the lower shaft seals, we found the threaded stud on the bottom of one of the shafts was damaged and had signs of thread damage and galling. This was most likely from a stainless steel nut on stainless steel threads that was installed and removed without the proper never seize lubricant. This compromised the re-installation of the stabilizer fin nut so we recommended removing the shaft to repair in our machine shop,Straight Line Marine. Once in the machine shop, we found that the stabilizer shaft was bent 0.080 which is significant for a stabilizer shaft. When we started the straightening process, which involves applying hydraulic force on the high point of the shaft, the stabilizer shaft cracked in two. This was a first never had that happen before. Under examination of the broken ends, it is evident that a crack in the shaft had worked its way to 20% through we just finished off the job. <\/p>\n
Cracked shaft <\/p>\n
This particular vessel is under new ownership so there is limited history as it relates to past problems and repairs. Obviously, this stabilizer was badly damaged at some point in the past. In all likelihood, the boat probably hit something or experienced a hard grounding which lead to a crack in the stabilizer shaft. Over time, these cracks tend to creep and grow. <\/p>\n
We were able to source a new stabilizer shaft from the manufacturer and complete the overhaul on the hydraulic stabilizer system. <\/p>\n
We have never experienced a stabilizer shaft cracking in two before in our machine shop, but it just goes to show that a small thing such as damaged threads can be a warning sign of bigger issues. <\/p>\n<\/p>\n
As mentioned in an earlier post, we were contracted by the new owner and captain of an older 135 foot Broward Yacht to do a number of running gear and hydraulic projects on the vessel. On the running gear side, we were tasked with removing the shafts, props and rudders to inspect and refurbish the components. From the shaft perspective, we inspected them to ensure they were straight and corrosion free. The machine shop found the shafts were slightly bent and required straightening. We also installed new cutlass bearings and repacked the stuffing box and performed an optical scope alignment before reinstalling the shafts back in the boat. <\/p>\n
As part of our standard maintenance and service process, we removed the rudders to check the bearings and packing glands. In this case, the bearings were in good shape so we did not have to replace them. We just needed to repack the stuffing boxes to complete the work on the rudder service. <\/p>\n
Maneuvering the rudders with lifts <\/p>\n
However, the challenge with removing and re-installing rudders on a yacht of this size comes with handling them. Each rudder weighs in excess of 800 pounds. In order to do the job right, and safely, it takes precision forklift work. We use two lifts to start the process, one to stand the rudder in a vertical position while the second secures the rudder so that it can be moved back to the boat. <\/p>\n
Its a matter of inches <\/p>\n
Maneuvering the rudders to align the rudder shaft with the opening in the boat many times translates into a matter of moving the forklift just fractions of an inch one way or the other. <\/p>\n<\/p>\n<\/p>\n
After considerable team work between the mechanics and the forklift operators, we successfully re-installed the rudders and now the yacht is good to go with a complete running gear overhaul complete. <\/p>\n<\/p>\n
Its not unusual for mega yachts to haul out at Lauderdale Marine Center requiring extensive work on multiple parts of the boat. That was the case for a 135 foot Broward when she came into the yard. The Captain of the yacht approached High Seas with a laundry list of requirements that included hydraulics and running gear jobs. High Seas is unique in the sense that we have the expertise to work on both areas, providing a central point of contact that can help to design the most efficient work flow through coordinated schedules. <\/p>\n
For this yacht, we were hired to: <\/p>\n
In coming posts, we will walk through the steps we took to make this yacht ship shape again. <\/p>\n
To accommodate the growing marine trade at LMC and the potential for larger yachts visiting the yard for service when the new, more powerful travel lift is installed, we have upgraded and enhanced our own lifting capabilities with the installation of a new 2 ton crane along with a new 1\/2 ton crane in our machine shop, Straight Line Marine. The new equipment will allow us to extended our shaft fabricating and straightening capabilities to more vessels hauling out at LMC. <\/p>\n
It is critical to make sure your shaft seal system is getting proper forced water cooling. If there is a temporary loss of cooling, the internal bearing on the Tides Seal assembly will become damaged or wear out quickly. Once damaged the seal assembly could spin with the shaft and come loose. This results in a leaking seal. <\/p>\n
Most experienced mechanics will see the leak and recommend replacing the seal. This can be done easily in the water if you have a spare seal on the shaft. However, before changing a seal you should determine if the assembly is damaged. Placing a new seal in a damaged assembly is a waste of time and a good seal. It will still leak. <\/p>\n
The internal bearing in the Tides Seal assembly should be 0.016 larger than the shaft. This keeps the assembly riding on the shaft and within the tolerance of the lip seal. There is a simple test that you can perform on the Tides Seal in your engine room to determine if the internal bearing has failed or become worn. As you will see in this video, place your hand under the seal assembly and pull straight up. If the bearing is damaged or worn, you can lift the assembly 1\/8 or more and water will squirt in. If the bearing is still within tolerance, it will feel like you cannot move it at all on the shaft. <\/p>\n
The adjacent photos show cut-away of the Tides Seals assembly with the internal bearing and shaft. <\/p>\n
If you do have a damaged bearing the only option is to replace the assembly. This means the shaft needs to come off the transmission, slid back and coupler removed. There are divers that can plug the stern tube to do this in the water if you are well prepared and experienced. <\/p>\n
When one of our returning customers, an 87 foot Broward yacht discovered that they had significant corrosion on their stern tubes (shaft logs), they asked our running gear experts to help out. Once we removed the shafts from the boat, we were able to get a better idea of what we were dealing with on the stern tubes. The vessel is made of aluminum and was suffering from corrosion to the point where we would need to fabricate new tubes. <\/p>\n
Scoping to align stern tube <\/p>\n
To accomplish this, we enlisted our machine shop, Straight Line Marine. The machine shop ensured the inner diameter was machined for the cutlass bearings, drilled & tapped for alignment jacking screws and milled out water vents. Once we finished the machining process, it was time to install the new stern tubes back into the boat. The stern tubes have a cutlass bearing on each end so it is critical that the tube be aligned properly to the struts and engines. To ensure that the stern tubes would be in perfect alignment, we used a process called optical scope alignmentor scoping for short. Scoping is the most advanced method for obtaining a perfect marine shaft alignment with struts, shaft logs, engines or v-drives. Scoping is the latest generation of alignment technology and far more advanced than the old piano wire system and even laser alignments. <\/p>\n
Welded stern tube in pace after optical alignment <\/p>\n
The twist here is that we used the scoping process to help the welders perfectly place the new stern tubes in the boat. With the welding complete, we were able to finish the job and ensure that the shaft and stern tubes were aligned, guaranteeing a vibration free ride for this valued customer. <\/p>\n
A 100 foot Marlow yacht was recently hauled at Lauderdale Marine Center for routine maintenance that included her running gear, hydraulics, topside paint and other services. The captain turned to High Seas Yacht Service for the ships running gear work and our sister company, High Seas Hydraulics for the hydraulic portion. <\/p>\n
Old pitted shafts <\/p>\n
During the inspection of the bearings and seals, we found that the shafts were deeply pitted to the point that we could not fix them through a cladding or weld-over process. New shafts would need to be fabricated. To make the new shafts, were turned to Straight Line Marine, our full service machine shop dedicated to shaft, strut and rudder straightening for precision alignments and the elimination of running gear vibration. At Straight Line Marine, we can straighten or fabricate shafts up to 6 inches indiameter and performshaftweld-overs (cladding).We areABS Certifiedfor Aquamet Stainless Steel Shaft Cladding. We also perform ABS shaft crack testing and straightening. <\/p>\n
For this yacht, we needed to make 4 diameter shafts starting with sourcing the raw materials, machining the right coupler taper and the threading on the propeller end of the shaft. We also had to machine the new key way for the <\/p>\n
Machining new key way <\/p>\n
shaft. <\/p>\n
As is common in many boats, this one used a coupler nut attachment with one big nut on the coupler end in the engine room. The nut that was used would be similar to a propeller nut. Since the coupler nut is usually recessed into the coupler, it takes a very large socket to tighten or loosen it. In order to perform the work, we would have to make custom sockets that would fit on a 1 wrench and then, because of the amount of torque required, put a 3 foot long pipe on the wrench to get the leverage. Because this work is happening in a very tight place, we found that we do not have enough room to swing a long pipe or get the socket in place. <\/p>\n
New coupler nut <\/p>\n
A more modern approach is the keeper plate or shaft locking plate. The end of the shaft is cut flush, drilled and tapped for much smaller bolts. Three hardened bolts are torqued down in a circle to draw the plate and coupler onto the shaft taper. A common socket can be used on a regular or wrench. We no longerneededlong cheater pipes since the torque required to draw up the plate is considerably less than that required on one big nut. <\/p>\n
This yacht now sports brand new shafts and is ready for smooth sailing. <\/p>\n<\/p>\n
Scored rods <\/p>\n
A customer walked into our sister company, High Seas Hydraulics with three leaking Quantum Stabilizer cylinders from a 150 foot Trinity motor yacht. Upon close inspection, it was determined that there were fine scores or scratches in the hydraulic rods that were causing the fluid to bypass the seals. These scratches could not be repaired or polished out so new hydraulic rods would need to be installed. <\/p>\n
Raw materials <\/p>\n
That is when our hydraulic teams turned to our machine shop Straight Line Marine. Through our procurement department at High Seas, we were able to source the raw materials needed to fabricate new hydraulic rods within a day. <\/p>\n
Finished rod <\/p>\n
The Straight Line Marine machinist went to work and crafted new rods to exact specifications including intricate thread machining. <\/p>\n
The ability to bring the stabilizer cylinders back to top working order with new hydraulic rods fabricated on-site in our machine shop saved this motor yachts owner and captain both time and money and was completed from a one stop company. <\/p>\n<\/p>\n
A 156 Custom Motor Yacht was hauled at Lauderdale Marine Center for a new paint job and other routine maintenance. As part of the painting process, the hydraulic side boarding ladder was removed by our Hydraulics team at High Seas Hydraulics for disassembly in order to paint the parts. The mechanical project was fairly straight forward. We made new pins and bushings in our machine shop, Straight Line Marine to replace some that were corroded in place and to provide for smoother operations of the ladder. <\/p>\n
Using a forklift to reinstall ladder <\/p>\n
The tricky part of the job was getting the ladder on and off of a boat of this size with the vessel blocked in the yard and surrounded by scaffolding. Careful use of a forklift and skilled technicians from bothour hydraulics but also from our running gear teams made the job a success. <\/p>\n
Our on-site services ranging from hydraulics work, machine shop capabilities and skilled technicians from all three of our companies define team work in getting the big jobs done right. <\/p>\n<\/p>\n<\/p>\n
Our dedicated machine shop, Straight Line Marine, was featured in a cover story in the January\/February issue of Professional BoatBuilder Magazine. The article titled The Necessity of Straight provides an in-depth look at the art of shaft alignments. The author visited our facilities at Lauderdale Marine Center for a refresher course in the practice and precisions required to get running gear alignments right. The article also touches on our new Hydraulics division and its capabilities. <\/p>\n Here is the original post:<\/p>\n High Seas Yacht Service | Specializing in Marine Propulsion Alignments<\/a><\/p>\n","protected":false},"excerpt":{"rendered":" When a 58 Kady Krogen trawler recently hauled out at Lauderdale Marine Center, our hydraulics company, High Seas Hydraulics was hired to do routine service on the ABT Trac hydraulic stabilizer system. Continue reading